[Bonmin] A couple of compilation questions

[Saqib Ilyas]

Thanks Pierre. I did a make distclean and then re-configured and make. It
all compiles now. I have bonmin exe as well as ipopt, cbc, and clp in the
bin directory. cbc even supports AMPL. However, when invoked, I get a MA27AD
not found in libhsl.so.
I had followed the instructions of copy pasting the Fortran code from the
HSL site into MA27AD.f and so on, and then ran configure. Any further clues?

On Thu, Aug 12, 2010 at 2:31 PM, Pierre Bonami <pierre.bonami at gmail.com>wrote:

> Then ASL did not configure correctly. I would retry configuring from
> scratch in a new directory. You can also check that the file config.log
> contains the following lines:
>
> configure:20916: checking whether code for third party package ASL is
> available
> configure:20938: result: yes
>
> Best,
> Pierre
>
> On Thu, Aug 12, 2010 at 11:06 AM, Saqib Ilyas <msaqib at gmail.com> wrote:
>
>> I'm afraid not. There's only ThirdParty/HSL in there.
>>
>>
>> On Thu, Aug 12, 2010 at 2:04 PM, Pierre Bonami <pierre.bonami at gmail.com>wrote:
>>
>>> From the directory where you built bonmin do you have the file
>>> ThirdParty/ASL/amplsolver.a ?
>>>
>>>
>>> On Thu, Aug 12, 2010 at 10:55 AM, Saqib Ilyas <msaqib at gmail.com> wrote:
>>>
>>>> Yes, I did. And I used the --with-asldir=BUILD in conjunction with
>>>> ../configure -C. Have done make clean, make again, but to no avail.
>>>>
>>>>
>>>>
>>>> On Thu, Aug 12, 2010 at 1:46 PM, Pierre Bonami <pierre.bonami at gmail.com
>>>> > wrote:
>>>>
>>>>> Hi,
>>>>> Did you download all the third parties (in particular the ASL library)?
>>>>> Best,
>>>>> Pierre
>>>>>
>>>>>   On Wed, Aug 11, 2010 at 3:36 PM, Saqib Ilyas <msaqib at gmail.com>wrote:
>>>>>
>>>>>>  Hi all
>>>>>> I've built Bonmin 1.3.2 on FC 9 Linux today.
>>>>>> 1- I see that the build/bin folder contains only two binaries: cbc and
>>>>>> clp. No bonmin executable. Did I do something wrong?
>>>>>> 2- I can not invoke cbc with a -AMPL command line parameter. Did I
>>>>>> forget to include a parameter to use with ./configure?
>>>>>> Thanks and best regards
>>>>>>
>>>>>> --
>>>>>> Muhammad Saqib Ilyas
>>>>>> PhD Student, Computer Science and Engineering
>>>>>> Lahore University of Management Sciences
>>>>>>
>>>>>> _______________________________________________
>>>>>> Bonmin mailing list
>>>>>> Bonmin at list.coin-or.org
>>>>>> http://list.coin-or.org/mailman/listinfo/bonmin
>>>>>>
>>>>>>
>>>>>
>>>>
>>>>
>>>> --
>>>> Muhammad Saqib Ilyas
>>>> PhD Student, Computer Science and Engineering
>>>> Lahore University of Management Sciences
>>>>
>>>> _______________________________________________
>>>> Bonmin mailing list
>>>> Bonmin at list.coin-or.org
>>>> http://list.coin-or.org/mailman/listinfo/bonmin
>>>>
>>>>
>>>
>>
>>
>> --
>> Muhammad Saqib Ilyas
>> PhD Student, Computer Science and Engineering
>> Lahore University of Management Sciences
>>
>> _______________________________________________
>> Bonmin mailing list
>> Bonmin at list.coin-or.org
>> http://list.coin-or.org/mailman/listinfo/bonmin
>>
>>
>


-- 
Muhammad Saqib Ilyas
PhD Student, Computer Science and Engineering
Lahore University of Management Sciences
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://list.coin-or.org/pipermail/bonmin/attachments/20100812/65a9de42/attachment.html