[Bonmin] A couple of compilation questions

[Andreas Waechter]

HI,

> copy pasting the Fortran code from the HSL site into MA27AD.f

It should be "ma27ad.f" in small letters.

Andreas

On Thu, 12 Aug 2010, Saqib Ilyas wrote:

> Thanks Pierre. I did a make distclean and then re-configured and make. It
> all compiles now. I have bonmin exe as well as ipopt, cbc, and clp in the
> bin directory. cbc even supports AMPL. However, when invoked, I get a MA27AD
> not found in libhsl.so.
> I had followed the instructions of copy pasting the Fortran code from the
> HSL site into MA27AD.f and so on, and then ran configure. Any further clues?
>
> On Thu, Aug 12, 2010 at 2:31 PM, Pierre Bonami <pierre.bonami at gmail.com>wrote:
>
>> Then ASL did not configure correctly. I would retry configuring from
>> scratch in a new directory. You can also check that the file config.log
>> contains the following lines:
>>
>> configure:20916: checking whether code for third party package ASL is
>> available
>> configure:20938: result: yes
>>
>> Best,
>> Pierre
>>
>> On Thu, Aug 12, 2010 at 11:06 AM, Saqib Ilyas <msaqib at gmail.com> wrote:
>>
>>> I'm afraid not. There's only ThirdParty/HSL in there.
>>>
>>>
>>> On Thu, Aug 12, 2010 at 2:04 PM, Pierre Bonami <pierre.bonami at gmail.com>wrote:
>>>
>>>> From the directory where you built bonmin do you have the file
>>>> ThirdParty/ASL/amplsolver.a ?
>>>>
>>>>
>>>> On Thu, Aug 12, 2010 at 10:55 AM, Saqib Ilyas <msaqib at gmail.com> wrote:
>>>>
>>>>> Yes, I did. And I used the --with-asldir=BUILD in conjunction with
>>>>> ../configure -C. Have done make clean, make again, but to no avail.
>>>>>
>>>>>
>>>>>
>>>>> On Thu, Aug 12, 2010 at 1:46 PM, Pierre Bonami <pierre.bonami at gmail.com
>>>>>> wrote:
>>>>>
>>>>>> Hi,
>>>>>> Did you download all the third parties (in particular the ASL library)?
>>>>>> Best,
>>>>>> Pierre
>>>>>>
>>>>>>   On Wed, Aug 11, 2010 at 3:36 PM, Saqib Ilyas <msaqib at gmail.com>wrote:
>>>>>>
>>>>>>>  Hi all
>>>>>>> I've built Bonmin 1.3.2 on FC 9 Linux today.
>>>>>>> 1- I see that the build/bin folder contains only two binaries: cbc and
>>>>>>> clp. No bonmin executable. Did I do something wrong?
>>>>>>> 2- I can not invoke cbc with a -AMPL command line parameter. Did I
>>>>>>> forget to include a parameter to use with ./configure?
>>>>>>> Thanks and best regards
>>>>>>>
>>>>>>> --
>>>>>>> Muhammad Saqib Ilyas
>>>>>>> PhD Student, Computer Science and Engineering
>>>>>>> Lahore University of Management Sciences
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> Bonmin mailing list
>>>>>>> Bonmin at list.coin-or.org
>>>>>>> http://list.coin-or.org/mailman/listinfo/bonmin
>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>> --
>>>>> Muhammad Saqib Ilyas
>>>>> PhD Student, Computer Science and Engineering
>>>>> Lahore University of Management Sciences
>>>>>
>>>>> _______________________________________________
>>>>> Bonmin mailing list
>>>>> Bonmin at list.coin-or.org
>>>>> http://list.coin-or.org/mailman/listinfo/bonmin
>>>>>
>>>>>
>>>>
>>>
>>>
>>> --
>>> Muhammad Saqib Ilyas
>>> PhD Student, Computer Science and Engineering
>>> Lahore University of Management Sciences
>>>
>>> _______________________________________________
>>> Bonmin mailing list
>>> Bonmin at list.coin-or.org
>>> http://list.coin-or.org/mailman/listinfo/bonmin
>>>
>>>
>>
>
>
> -- 
> Muhammad Saqib Ilyas
> PhD Student, Computer Science and Engineering
> Lahore University of Management Sciences
>