<br><font size=2 face="sans-serif">Edgardo,</font>
<br>
<br><font size=2 face="sans-serif">You can use setDetailMessages (examples
in Cbc/Samples) to set the detail level for all messages &lt; 6000 to high.</font>
<br>
<br><font size=2 face="sans-serif">At present the best way would be to
use one form of setDetailMessages to switch off all messages and then switch
back the &gt;= 6000 messages one by one.</font>
<br>
<br><font size=2 face="sans-serif">As that seems inelegant I will add a
new setDetailMessage to do by range. &nbsp;Then it would be</font>
<br>
<br><font size=2 face="sans-serif">.messageHandler()-&gt;setDetailMessage(3,0,5999);</font>
<br>
<br><font size=2 face="sans-serif">Should be in a few hours.</font>
<br>
<br><font size=2 face="sans-serif">John Forrest</font>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td width=40%><font size=1 face="sans-serif"><b>Edgardo Fuchs &lt;edgardo_fuchs@mi.cl&gt;</b>
</font>
<br><font size=1 face="sans-serif">Sent by: coin-discuss-bounces@list.coin-or.org</font>
<p><font size=1 face="sans-serif">12/02/2005 07:19 PM</font>
<table border>
<tr valign=top>
<td bgcolor=white>
<div align=center><font size=1 face="sans-serif">Please respond to<br>
edgardo_fuchs and Discussions about open source software for Operations
Research &nbsp; &nbsp; &nbsp; &nbsp;</font></div></table>
<br>
<td width=59%>
<table width=100%>
<tr>
<td>
<div align=right><font size=1 face="sans-serif">To</font></div>
<td valign=top><font size=1 face="sans-serif">COIN &lt;coin-discuss@list.coin-or.org&gt;</font>
<tr>
<td>
<div align=right><font size=1 face="sans-serif">cc</font></div>
<td valign=top>
<tr>
<td>
<div align=right><font size=1 face="sans-serif">Subject</font></div>
<td valign=top><font size=1 face="sans-serif">[Coin-discuss] Message control</font></table>
<br>
<table>
<tr valign=top>
<td>
<td></table>
<br></table>
<br>
<br>
<br><font size=3>Dear COIN list,<br>
<br>
I need to control the message output, prinitng only those messages with
return code greater or equal than 6000 (ie warning or error).<br>
<br>
I tried using setLogLevel, but even level 1 is too verbose, including informational
messages.<br>
<br>
Is there another option to control the output in that way, or do I need
to write a message handler function?<br>
<br>
Regards,<br>
Edgardo Fuchs<br>
</font>
<br><font size=3><tt>-- <br>
<br>
Edgardo Fuchs<br>
<br>
Santiago, Chile<br>
<br>
Tel: +56 (2) 435 0090<br>
Cel: +56 9837 8433<br>
</tt></font><font size=2><tt>_______________________________________________<br>
Coin-discuss mailing list<br>
Coin-discuss@list.coin-or.org<br>
http://list.coin-or.org/mailman/listinfo/coin-discuss<br>
</tt></font>
<br>